Fire Sprinkler Water Pipe Marker

Fire Sprinkler Water Pipe Marker
Item #
1F9B R/W
Wrap Around Marker Reads
Fire Sprinkler Water
Wrap Around Marker Design
Directional Arrow






Price: $3.45
Low Price Guarantee
0 In Stock
Special freight arrangements are necessary. Learn More

Need a quote for a large order? Call 800−274−6271 or email us.

Fire sprinkler water pipe markers meet specification compliances for ANSI / ASME A13.1 standards for the identification of fire sprinkler system pipes. No pipe preparation is needed for these markers. Fire sprinkler water pipe markers are available in wrap-around and strap-on formats for pipe outside diameters ranging from 1/2 inch to over ten inches and provide 360 degree visibility. 2 nylon ties are included with all markers for pipes with an outside diameter of 6-1/8" and larger so they can be easily affixed to the pipe.

  • Fire Protection Water Pipe Marker 1F1
  • Fire Auto Sprinklers Pipe Marker 1F40
  • Sprinkler Fire Pipe Marker 1S15
  • Sprinkler Water Pipe Marker 1S2
  • Sprinkler Pipe Marker 1S40

Product Information


System # 1 Markers: Wrap Around and Strap On Markers

These markers are manufactured with rigid vinyl, surface is printed with UV ink and then thermoformed. Thermoformed pipe markers are styles AA thru H (pipes 1" thru 6"). These markers are simply uncoiled by hand, and automatically recoiled around the pipe. Marker sizes C, D, E are supplied with a 1/2" wide strip of 3M™ 467 adhesive which only needs to be released when there is a constant pipe temperature of 120 degrees or more. Marker styles F thru H (pipes over 6") are not thermoformed because of their size, they are installed using nylon ties. Style F is supplied with two 34" long ties, styles G and H are supplied with two 48" long ties. For pipes larger than 14" in diameter order additional nylon ties.

  • These Markers are available in 2 ways, Coiled (Wrap Around) and flat with holes (Strap On).
  • For pipe diameters 3/4" thru 6" use Wrap Around Markers (Styles AA, A, B, C, D, E) these markers are simply uncoiled by hand and automatically recoil around the pipe.
  • For pipe diameters 6" or larger use Strap On Markers (Styles F, G, H) these markers are installed using nylon ties or S.S. Strapping, Brimar supplies a pair of nylon ties with each of these markers.
  • Advantages of System #1 Markers: No pipe preparation, 360° visibility, speed of installation, arrows included and overall better appearance.
4 to 5 years outdoors
Service Temp
-40 to 160° F
Minimum Application Temp
Surface Prep
Spec Compliance
ANSI / ASME A13.1 2020
System 1 Sizes

Marker Size, Letter Height & Max. Characters Per Marker

The following shows the recommended pipe marker letter height and marker size based on the outside pipe diameter of the pipe to be identified. For pipes smaller than 3/4" and for valve identification, the use of a permanent legible tag is recommended.

System 1 Sizes

ANSI / ASME Size Table

Size AA A B C D E F G H
Pipe O.D. 3/8″ to 1/2″ 3/4″
to 1″
to 2-3/8″
to 3-1/4″
to 4-1/2″
to 6″
to 7-7/8″
8″ to 10″ over 10″
Marker Length 3″ 8″ 8″ 12″ 12″ 12″ 12″ 24″ 32″
Letter Size 0.25″ 0.50″ 0.75″ 1.3″ 1.3″ 1.3″ 1.3″ 2.5″ 3.5″

* Size selection MUST include insulation thickness / Size F ships with two 36" long ties and sizes G and H ship with two 48" long nylon ties.

Latest Revision ANSI / ASME A13.1

ANSI / ASME is the most common pipe identification standard used in the United States. The standard specifies the primary and secondary means of identifying pipe content, as well as the size, color and placement of the identification device.

1. Primary Identification

The legend (name of pipe content) and directional flow arrow remain the primary means of identifying pipe content. The size and placement of the marker and arrow has not changed. See ANSI / ASME size table and installation recommendations for details.

Legends should use arrows to indicate the direction of flow, where flow can be in both directions, arrows in both directions should be displayed. Contents should be identified by a legend with sufficient additional details such as temperature, pressure, etc. Legends should be brief, informative, pointed, and simple for greatest effectiveness.

Marker illustration

1.1 Additional Means of Identification ASME A13.1

ASME A13.1 incorporated the GHS pictograms into the 2015 revision and has recommended their use as part of the legend.

"The applicable GHS pictograms as illustrated in Fig.1 may be included as part of the legend. Where piping is connected to containers that are labeled in accordance with GHS requirements, a corresponding label on the piping may be provided. The corresponding label should contain at least the product name or identifier, the pictogram, the signal word, and the physical, health, and environmental hazard statements."

GHS Pictogram

2. Secondary Identification

ASME A13.1 4.2 Color: "Color should be used to identify the characteristic hazards of the contents. Color should be displayed on, or contiguous to, the piping by any physical means, but its use shall be used in combination with a legend. Color may be used in continuous, total-length coverage or in intermittent displays. Colors preceded by the word "Safety" shall meet the requirements of ANSI / NEMA Z535.1"

Fire Quenching Fluids

Safety Red Background / White Legend

Toxic & Corrosive Fluids

Safety Orange Background/ Black Legend

Flammable Fluids

Safety YellowBackground / Black Legend

Combustible Fluids

Safety Brown Background /White Legend

Potable, Cooling, Boiler feed, & other Water

Safety Green Background/ White Legend

Compressed Air

Safety Blue Background / White Legend

Defined by the User

Safety Purple Background / White Legend

Defined by the User

Safety White Background / Black Legend

Defined by the User

Safety Gray Background / White Legend

Defined by the User

Safety Black Background / White Legend

Flammable Fluids
Used for fluids that, under ambient or expected operating conditions, are a vapor or procedure vapors that can be ignited and continue to burn in air. The terms thus may apply, depending on service conditions, to fluids defined for other purposes as flammable or combustible
Oxidizing Fluids
Oxidizing fluid is any gas or liquid that may, generally by providing oxygen, cause or contribute to the combustion of other material more than air does.
Fire Quenching Fluids
This classification includes water, foam and CO2 used in sprinkler systems and fire fighting piping systems.
Toxic & Corrosive Fluids
This classification includes fluids that are corrosive or toxic, or will produce corrosive or toxic substances when released.
Combustible Fluids
This classification includes fluids that can burn but are not flammable.

3. Placement

Marker visibility

Always position pipe labels on pipes to achieve the best visibility. Install pipe labels below or above the horizontal centerline of the pipe when pipes are located above or below the normal line of vision.

Pipe marker illustration
Install pipe labels close to valves or flanges.
Plastic Lockout Hasp 428 C3504
Apply pipe labels adjacent to changes in direction and/or branches.
Marker installation options
Install pipe labels before and after all wall, floor and ceiling penetrations.
Marker installation options
Install pipe labels at frequent intervals on straight pipe runs Brimar recommends 20 to 25ft.

4. Abandoned Piping

Piping that has been abandoned in place should be identified. The recommended color scheme is a safety white background with black letters. A black border should be added to the identification. When the abandoned piping is protected from corrosion by the addition of a pressurized fluid or contains residual hazardous material, the legend should indicate that.



Your cart is empty.