SNAP'n SAFE Surface Mount Breakaway Anchor For U-Channel Post
- Item #:
Other configurations of this product
- NCHRP 350 Approved
SNAP'n SAFE Surface Mount Breakaway Anchor For U-Channel Post is an NCHRP 350 compliant breakaway base that is designed with a 360° shear point that will prevent the u-channel sign post from striking and penetrating the windshield or roof of a vehicle when impacted during a collision.
This product is ideal for locations where installing an anchor post is not suitable, such as parking garages, parking lots, and concreete medians.
This base fits 2 lbs./ft., 3 lbs./ft., and 4 lbs./ft. U-channel posts, and the is intended for concrete surfaces only. It is not to be used on asphalt surfaces due to structural integrity issues with asphalt. It weighs 10 lbs. and is made of cast gray iron, 80% of which is recycled material. It can also withstand winds of up to 120 mph. All ground mounting and post mounting hardware is included.
7″ Base For 2, 3, and 4 lbs./ft. U-Channel Posts
|Cast Gray Iron||Y3541-USMB||$132.75|
2 lbs/ft U-Channel Post
Y3432, Y3486, Y3434, Y3437
Bolting Set (2 bolts, 2 nuts, 4 washers)
Y4931, Y4899, Y3465
Tamperproof Set (2-bolts, 2-nuts, 4-washers)
Y4900, Y4901, Y3551
3" Ribbed Aluminum Sign Saver Plates
180 Degree Flat Blade U-Channel Post Street Name Sign Bracket
90 Degree Flat Blade U-Channel Post Street Name Sign Bracket
90 Degree Cross Piece For Flat Blade Street Name Signs
2-Way Adjustable Cross Piece For Flat Blade Street Name Signs
Adjustable U-Channel Bracket For Flat Blade Street Name Signs
Adjustable Cross Separator For Flat Blade Street Name Signs
180 Degree Extruded Blade U-Channel Post Street Name Sign Bracket
90 Degree Extruded Blade U-Channel Post Street Name Sign Bracket
90 Degree Cross Piece For Extruded Blade Street Name Signs
2-Way Adjustable Cross Piece For Extruded Blade Street Name Signs
Adjustable U-Channel Bracket For Extruded Blade Street Name Signs
Adjustable Cross Separator For Extruded Blade Street Name Signs
One Way Bolts
Y4911TB, Y4912TB, Y3552
5/16" Break-Away Nuts
5/16" Nylon Washers
5/16" Zinc Plated Washers
SNAP'n SAFE™ U-Channel Post Surface Mount Breakaway
This SNAP'n SAFE™ Breakaway Device is made of cast gray iron, and withstands winds of 120 MPH. Made from 80% recycled materials.
Installation instructions are included with every SNAP'n SAFE U-Channel post surface mount breakaway device. It is recommended that this breakaway be installed in concrete surfaces only due to the strength of concrete as compared to asphalt.
- ½″ socket and ratchet wrench
- 9/16″ socket and ratchet wrench
- Remove any burrs or imperfections from the 2 lbs./ft., 3 lbs./ft., or 4 lbs./ft. sign post.
- Check hole location of the sign post and anchor post. The bottom hole of the sign post must be ½″ on center (+/- ⅛″) from the end of the sign post.
- Determine the location for the surface mount coupler.
(Please note that all bolts must be at least 5 inches from all concrete edges.)
- Place surface mount coupler on the concrete surface and place the sign post on top of the coupler. Using a level, determine if any washers are needed under the base at the hole location to level out the sign post.
- Using the surface mount coupler as a template, mark the location of the three (3) holes to drill. With a ⅜ inch drill bit, drill three (3) holes at least 4½″ deep. It is not necessary to blow the holes out or clean them out.
- Clean off concrete surface and align the coupler with the holes. Place any necessary washers under the base as determined in Step 4.
- Put one (1) washer on each bolt and install the three (3) bolts. (DO NOT tighten all the way until you are certain that the base is level and all three (3) hole locations are firmly resting on the washers or concrete.)
Note: The bolts are carbon steel and are extremely hard. They have a 3,800 pound pull-out strength.
- Align the sign post to the SNAP'n SAFE coupler and attach using the (2) hex bolts, (2) nuts, and (2) washers.
MAX TORQUE = 19 FT LBS.