16" Street Name Sign Wing Bracket - Y3516, Sign Mounting Hardware

16" Street Name Sign Wing Bracket

16" Street Name Sign Wing Bracket
Item #
Y3516-WG16

Note:

Holes on sign are not required when using this bracket.

Size:

Material:

Laminate:

Mounting:

Packaging:

Qty
Each
1–4
17.95
5–9
16.95
10+
15.45
Price: 17.95
0 In Stock
Special freight arrangements are necessary. Learn More.

Need a quote for a large order? Call 800-274-6271 or email us.

The 16" Wide Wing Bracket is the ideal solution for mounting street name signs as well as smaller parking or traffic signs on large round posts and poles. When used for its primary purpose of mounting street name signs, these can accommodate both flat blade and extruded blade type street signs, and is best suited for street name signs up to 24" long.

These wing brackets also have three 3/8" mounting holes which allow them to be installed on wood posts, and three well-defined slots that fit up to 3/4" stainless steel strapping, helping to keep the bracket in place during the installation.

Each 16" Wing Bracket For Street Name Signs includes set screws for securing the sign to the bracket. No holes are required on the street name sign for installation. A 5/32" hex key is necessary to tighten the set screws.

This bracket can also be mounted on a 2 lbs./ft. U-Channel Post (Part # Y3434), together with 2½″ bolting set (Part # Y3465 or Y4904TS). When installing wing bracket on post, use the top and bottom holes on the bracket. Our mounting hardware is sold in sets of 2 bolts, nuts and washers. View image.

Product Information

Details

Street Name Sign Wing Brackets

The street name sign wing bracket is designed to hold street name signs on large round posts and poles so that the sign in perpendicular to the pole. These brackets will accommodate .080″ flat blade signs and extruded blade signs as well as 6″ and 9″ tall signs.

16 inch street name wing bracket
24 inch street name wing bracket

Tools required for installation:

Installation steps:

  1. Measure out enough stainless-steel strapping to go around the pole including an extra 12″ or so of slack.
  2. Insert one end of the strapping into your buckle or wing seal and bend about 2″ to 3″ of strapping underneath the wing seal or buckle.
  3. Wrap the strapping around the pole and slide the other end of the strapping through the buckle or wing seal and bend it back so that the strapping stays in place.
  4. Take your wing bracket and insert the middle of it under the strapping. Two people may be needed for this step to hold the bracket in place.
  5. Tighten the strapping down with the strapping tool, making sure that the tool is against the wing seal or buckle during this step.
  6. Once the strapping is tight, bend the strapping with the tool to hold the tension and use the cutter to cut off the excess strapping.
  7. Fold the excess strapping over the buckle or wing seal and hammer down the wings to secure the strapping.
  8. Repeat these steps to install the other two bands of strapping.
  9. Place your street name sign in the bracket.
  10. Tighten down the set screws using the 5/32″ hex key.
Strapping being inserted into the buckle
Strapping being inserted into the buckle
Strapping being inserted into wing seal
Strapping being inserted into wing seal
The other end of the strapping being inserted and bent to hold it in place
The other end of the strapping being inserted and bent to hold it in place
Wing bracket being put under strapping
Wing bracket being put under strapping
Tightening the strapping around the pole with tool number Y3532
Strapping tool Y3532 tightening the strapping around the pole
Tightening the strapping around the pole
Same process with a different tool Y3533 tightening the strapping around the pole
Wing bracket mounted onto pole and strapping cut to size
Wing bracket mounted onto pole and strapping cut to size
Extra strapping left over to be sealed under buckle or wing seal
Extra strapping left over to be sealed under buckle or wing seal
Bend the strapping over the buckle or wing seal to partially secure the strapping
Bend the strapping over the buckle or wing seal to partially secure the strapping
Wing seal or buckle being closed to secure the strapping
Wing seal or buckle being closed to secure the strapping
Street name sign on wing bracket
Street name sign on wing bracket
Tightening set screws with Y3522 T-handle Hex Key
Tightening set screws with Y3522 T-handle Hex Key
Wing bracket used with street name sign on light pole

Reviews

800-274-6271
Cart

Your cart is empty.