16" Street Name Sign Wing Bracket
The 16" Wide Wing Bracket is the ideal solution for mounting street name signs as well as smaller parking or traffic signs on large round posts and poles. When used for its primary purpose of mounting street name signs, these can accommodate both flat blade and extruded blade type street signs, and is best suited for street name signs up to 24" long.
These wing brackets also have three 3/8" mounting holes which allow them to be installed on wood posts, and three well-defined slots that fit up to 3/4" stainless steel strapping, helping to keep the bracket in place during the installation.
Each 16" Wing Bracket For Street Name Signs includes set screws for securing the sign to the bracket. No holes are required on the street name sign for installation. A 5/32" hex key is necessary to tighten the set screws.
This bracket can also be mounted on a 2 lbs./ft. U-Channel Post (Part # Y3434), together with 2½″ bolting set (Part # Y3465 or Y4904TS). When installing wing bracket on post, use the top and bottom holes on the bracket. Our mounting hardware is sold in sets of 2 bolts, nuts and washers. View image.
|
16 x 8¼″
|
|||||
|---|---|---|---|---|---|
| Material | Sku | Quantity/Price | |||
|
|||||
| Cast Aluminum | Y3516-WG16 | $17.95 | $16.95 | $15.45 | |
Phone: 800-274-6271
Fax: 800-279-6897
- All
- Buckles
- Hardware
- Hex Tools
- Strapping
- Strapping Tools
- Wing Seals
5/32" Cushioned T-Handle Hex Key
Y3522
5/32" L-Handle Hex Key
Y3523
L-Handle Hex Key For Vandal Resistant Set Screws
Y3524
5/32" Hex Bit For Vandal Resistant Set Screws
Y3525
Vandal Resistant Set Screws
Y3526
Stainless Steel Strapping
Y3534
Stainless Steel Wing Seals
Y3528
Stainless Steel Buckles
Y3529
Ratchet Type Strapping Tool
RTST-1
Spinner Type Tensioner Tool
Y3532
One-Handed Ratchet Tool with Cutter
Y3533
Frequently Purchased Together
Wing Bracket
Y3518
Sign Bolting Set
Y4931, Y4899, Y3465, Y3550
Street Name Sign Wing Brackets
The street name sign wing bracket is designed to hold street name signs on large round posts and poles so that the sign in perpendicular to the pole. These brackets will accommodate .080″ flat blade signs and extruded blade signs as well as 6″ and 9″ tall signs.
 |
 |
Tools required for installation:
Installation steps:
- Measure out enough stainless-steel strapping to go around the pole including an extra 12″ or so of slack.
- Insert one end of the strapping into your buckle or wing seal and bend about 2″ to 3″ of strapping underneath the wing seal or buckle.
- Wrap the strapping around the pole and slide the other end of the strapping through the buckle or wing seal and bend it back so that the strapping stays in place.
- Take your wing bracket and insert the middle of it under the strapping. Two people may be needed for this step to hold the bracket in place.
- Tighten the strapping down with the strapping tool, making sure that the tool is against the wing seal or buckle during this step.
- Once the strapping is tight, bend the strapping with the tool to hold the tension and use the cutter to cut off the excess strapping.
- Fold the excess strapping over the buckle or wing seal and hammer down the wings to secure the strapping
- Repeat these steps to install the other two bands of strapping.
- Place your street name sign in the bracket.
- Tighten down the set screws using the 5/32″ hex key.
Strapping being inserted |
Strapping being inserted |
The other end of the strapping |
Wing bracket being |
Strapping tool Y3532 tightening |
Same process with a different tool Y3533 tightening the strapping around the pole |
Wing bracket mounted onto |
Extra strapping left over to be sealed under buckle or wing seal |
Bend the strapping over the buckle or wing seal to partially secure the strapping |
Wing seal or buckle being |
Street name sign |
Tightening set screws |
|
||
