New Jersey TRUSS SIGNS (Truss Roof / Floor Assembly Signs)

State of New Jersey TRUSS SIGNS

N.J.A.C. 5:70-2.20(a)1. “The emblem shall be of a bright and reflective color, or made of reflective material. The shape of the emblem shall be an isosceles triangle and the size shall be 12 inches horizontally by 6 inches vertically. The following letters, of a size and color to make them conspicuous, shall be printed on the emblem, as shown in diagram below.”

N.J.A.C. 5:70-2.20(a)2. “The emblem shall be permanently affixed to the left of the main entrance door at a height between 4 and 6 feet above the ground and shall be installed and maintained by the owner of the building.”

Sign Configuration

New Jersey Truss Construction Signs

NYCRR Truss Type Construction Signs

Subchapter C of Chapter XXXIII of Title 19 of the Official Compilation of Codes, Rules and Regulations of the State of New York is amended by adding a new Part 1264 to read as follows:

Part 1264
IDENTIFICATION OF BUILDINGS UTILIZING TRUSS TYPE CONSTRUCTION

1264.1 Introduction. Section 382-a of the Executive Law provides that commercial and industrial buildings and structures that utilize truss type construction shall be marked by a sign or symbol that informs persons conducting fire control and other emergency operations of the existence of truss construction. Section 382-a further directs the State Fire Prevention and Building Code Council to promulgate rules and regulations it deems necessary to carry into effect the provisions of the statute. This Part establishes certain requirements pertaining to the identification of buildings and structures that utilize truss type construction.

1264.2 Enforcement.
(a) Subdivision 4 of section 382-a of the Executive Law directs local governments to provide for enforcement of the statute. Enforcement of section 382-a of the Executive Law shall include enforcement of the provisions of this Part. A fee of fifty dollars shall be paid by the owner of a building with truss type construction to the authority having jurisdiction for enforcement of section 382-a of the Executive Law prior to the issuance of a building permit.

(b) This Part shall not apply within a city with a population of one million or more persons.

1264.3 Definition. For the purposes of this Part, truss type construction shall mean a fabricated structure of wood or steel, made up of a series of members connected at their ends to form a series of triangles to span a distance greater than would be possible with any of the individual members on their own. Truss type construction shall not include:
(1) individual wind or seismic bracing components which form triangles when diagonally connected to the main structural system; and
(2) structural components that utilize solid plate web members.

1264.4 Identification of truss type construction.

(a) Truss type construction shall be identified by a sign or signs in accordance with the provisions of this Part.

(b) Signs shall be affixed where a building or a portion thereof is classified as Group A, B, E, F, H, I, M, or S occupancy, and in hotels and motels classified as Group R-1 or R-2 occupancy, in accordance with the provisions for the classification of buildings set forth in chapter 3 of the Building Code of New York State (see 19 NYCRR Part 1221).

(c) Signs shall be provided in newly constructed buildings that utilize truss type construction and in existing buildings where an addition that extends or increases the floor area of the building utilizes truss type construction. Signs shall be affixed prior to the issuance of a certificate of occupancy or a certificate of compliance.

(d) Signs identifying the existence of truss construction shall consist of a circle 6 inches (152.4 mm) in diameter, with a stroke width of ½ inch (12.7 mm). The sign background shall be reflective white in color. The circle and contents shall be reflective red in color, conforming to Pantone matching system (PMS) #187. Where a sign is directly applied to a door or sidelight, it may be a permanent non-fading sticker or decal. Signs not directly applied to doors or sidelights shall be of sturdy, non-fading, weather resistant material.

(e) Signs identifying the existence of truss construction shall contain the roman alphanumeric designation of the construction type of the building, in accordance with the provisions for the classification of types of construction set forth in section 602 of the Building Code of New York State (see 19 NYCRR Part 1221), and an alphabetic designation for the structural components that are of truss construction, as follows: “F” shall mean floor framing, including girders and beams “R” shall mean roof framing “FR” shall mean floor and roof framing The construction type designation shall be placed at the twelve o’clock position over the structural component designation, which shall be placed at the six o’clock position.

(f) Signs identifying the existence of truss construction shall be affixed in the locations specified in Table I-1264.

Sign Configuration

New York Truss Construction Signs

TABLE I-1264: TRUSS IDENTIFICATION SIGN LOCATIONS

Florida TRUSS SIGNS (Truss Roof / Floor Assembly Signs)

69A-3.012 Standards of the National Fire Protection Association and Other Standards Adopted.
(1) Except as specifically modified by statute or by the State Fire Marshal’s rules, the Florida specific edition of NFPA 101, the Life Safety Code®, 2006 edition and the Florida specific edition of NFPA 1, the Uniform Fire Code2006 edition, as adopted within Rule Chapter 69A-60, F.A.C., entitled the “2007 edition of the Florida Fire Prevention Code,” are hereby adopted and incorporated by reference and are applicable to those buildings and structures specified in paragraphs (a) and (b) of subsection (1) of Section 633.022, F.S.

Excerpt from NFPA 101, the Life Safety Code®,
2006 edition and the Florida specific edition of NFPA 1, the Uniform Fire Code2006 edition:

Sign Configuration

New York Truss Construction Signs

TRUSS SIGN MATERIALS

Label Material: Engineering Grade (Type I) Reflective Aluminum:

Description & Attributes

Engineering Grade (EG) retro-reflective sheeting is a beaded plastic material that renders high retro-reflectivity at night. It is designed for use mainly on traffic signs and is highly resistant against the extremes of hot, cold, dry, and humid weathering conditions. Engineering Grade (EG) Reflective Sheeting meets ASTM D4956 Type I retro-reflective sheeting standards.

Rigid Material: Engineering Grade (Type I) Reflective Aluminum:

Description & Attributes

Engineering Grade (EG) retro-reflective sheeting is a beaded plastic material that renders high retro-reflectivity at night. It is designed for use mainly on traffic signs and is highly resistant against the extremes of hot, cold, dry, and humid weathering conditions. Engineering Grade (EG) Reflective Sheeting meets ASTM D4956 Type I retro-reflective sheeting standards.

3M High Intensity Prismatic Reflective Aluminum:

Description & Attributes

3M™ High Intensity Prismatic Reflective Sheeting is a non-metalized microprismatic lens reflective sheeting designed for production of reflective durable traffic control signs, work zone devices and delineators that are exposed vertically in service. 3M high intensity prismatic sheeting provides long-term reflectivity and durability.Its unique construction provides high levels of retroreflectivity for multiple traffic situations. 3M™ High Intensity Prismatic Reflective Sheeting meets and exceeds ASTM D 4956 Spec Type III, IV and X.